Landscape and Dock Lighting Planner

Waterfront and estate homes in South Florida

Size the transformer and the cable for your landscape and dock lighting

Low-voltage lighting fails when the transformer is too small, the cable runs are too long, or the fixtures corrode in salt air. Enter your runs of fixtures. The planner finds the transformer size, the cable size, the tap and the voltage at the fixtures of each run. It also shows salt-air notes and the sea turtle rules for a beach property.

For owners, landscape architects and builders. Free to use. Your inputs stay on this page.

ExampleA Broward County home on the Intracoastal with five runs and a dock. Change any value to plan your property.

Your property

We use the county for the sea turtle check.

Water near the property
Transformer taps
Fixture voltage range

Default: 10.8 to 15 V. The VOLT installation guide gives this range for LED fixtures. Use the range on your fixture data sheet.

Runs of fixtures

A run is one cable from the transformer to a group of fixtures. Enter the cable length from the transformer to the fixtures.

Result

Run map

Cable lengths to scale. Each dot is one fixture, up to 12 for each run.

Each run, with the math

We find the voltage drop on each run. Then we pick the lowest tap that keeps the fixtures in the voltage range. Open a run to see each step.

Coast and dock

Salt air, water and sea turtle rules change what you can install. We show only rules that we read in the official text or in the maker's guide.

Planning cost

This is a planning estimate for two parts only: the transformer and the cable. For fixtures, labor, permits and power on the dock, ask for a quote.

Send to a lighting designer

The brief has your inputs, the results and the sources. It is plain text.


        

What to do next

  1. Copy the brief. This page sends nothing.
  2. Paste it into an email or a message to a lighting designer.
  3. The designer checks the fixtures, the cable and the transformer for your property.
  4. A licensed electrician does the line-voltage work.

Questions

Why are the last fixtures on a run dimmer than the first fixtures?

The cable has resistance. The current in the cable uses some of the voltage before it gets to the fixtures. This loss is the voltage drop.

More watts, a longer run or a smaller cable gives more voltage drop. The VOLT plan guide gives an example: the first fixture gets 12 volts and the last fixture gets 9 volts.

Sources: MSU Tech Note 227, VOLT plan guide.

How large a transformer do I need?

Add the watts of all fixtures. Keep the total at or below 80% of the transformer rating. The VOLT installation guide gives this rule, and the VOLT plan guide says that most makers recommend it.

Then go up to the next common size: 150, 300, 600, 900 or 1,200 W. For example, 168 W of fixtures needs at least 210 W, so use a 300 W transformer.

Sources: VOLT installation guide, VOLT plan guide, Kichler sizes.

What does a multi-tap transformer do?

It has more than one output voltage. The VOLT multi-tap guide shows taps of 12, 13, 14 and 15 V. Connect a long run to a higher tap to make up for the voltage drop.

After the install, measure the voltage at the fixtures with a meter. Unplug the transformer before you move a cable to a different tap.

Source: VOLT installation guide, Quick Start Steps 10 and 11.

Which cable size do I need?

It depends on the watts on the run and the length of the run. The planner does the math for each run.

The VOLT plan guide also gives a quick check. Multiply the watts on the run by its length in feet:

  • 10,000 or less: 12 gauge cable.
  • 10,001 to 15,000: 10 gauge cable, or divide the run into two runs.

Keep each run to about 100 to 150 W. The VOLT installation guide does not recommend runs longer than 300 ft.

Sources: VOLT plan guide, VOLT installation guide.

Can I put low-voltage fixtures on my dock?

Check three things first. The maker must rate the fixtures for the location. The metals must suit salt air. A licensed electrician must do the line-voltage work, for example a new outlet near the water.

Ask the electrician which code rules apply to power on your dock.

If people on a nesting beach can see the dock, read the sea turtle rule for piers.

Sources: VOLT installation guide, Rule 62B-55 model ordinance, Sec. 3.8.

Which metals last in salt air?

FEMA Technical Bulletin 8 is about metal hardware near the coast. It says that stainless steel resists corrosion in salt air. It recommends Type 304 or Type 316, and Type 316 resists corrosion more.

When two different metals touch in salt water, one of them corrodes. So use similar metals for the screws, the brackets and the fixture.

Warranty terms also show the difference. VOLT gives a lifetime warranty on its brass and copper fixtures and 5 years on its aluminum fixtures.

Sources: FEMA Technical Bulletin 8, Sec. 5.1.2 and 8.2, VOLT warranty.

Do sea turtle rules apply to my landscape fixtures?

They can. Rule 62B-55.003 lists 26 Florida counties with nesting beaches. Miami-Dade, Broward, Palm Beach, Monroe, Martin, St. Lucie, Collier and Lee are on the list.

The state model ordinance covers each property with light that people on the beach can see. This includes properties that are not on the beach.

The model is guidance for local governments. Your county or city ordinance is the rule that applies. The Turtle-Safe Lighting Checker shows the local rule.

Source: Rule 62B-55, F.A.C., and the model ordinance, Sec. 2.1.

Can I put uplights on palms near a nesting beach?

The state model ordinance calls landscape lights and uplights non-egress lights. It allows them only on the landward side of buildings or other opaque structures.

They must use long wavelength light, 560 nm or longer, and people on the beach must not see them. Check your local ordinance before you buy fixtures.

Source: Model ordinance, Sec. 1.4 and Sec. 3.3.3.

Where do I put the transformer?

The VOLT installation guide gives these steps:

  • Mount the transformer upright, with the bottom at least 1 ft above the ground.
  • Plug it into a GFCI-protected outlet with an in-use cover.
  • Keep it at least 5 ft from a pool or spa and at least 10 ft from a fountain.
  • In hot climates, keep it out of direct sun.

A location near the middle of the fixtures keeps the runs short.

Source: VOLT installation guide, safety guidelines.

When do I bury the cable?

Bury it after you aim the fixtures. The VOLT installation guide says to make the last adjustments at dusk. Then bury the cable.

Leave extra cable at each fixture, so that you can adjust the fixtures at night.

Source: VOLT installation guide, Quick Start Steps 3 and 15.

How the planner works

1. Load

load = fixtures × watts each

The total load is the sum of all runs.

2. Transformer

size needed = total load ÷ 0.80

We go up to the next common size: 150, 300, 600, 900 or 1,200 W. Above 1,200 W, we use two or more transformers.

3. Voltage drop

current = load ÷ 12 V
resistance = ohms per 1,000 ft × length ÷ 1,000
voltage drop = 2 × current × resistance

The 2 counts both wires of the cable (MSU Tech Note 227, Equation 227.1).

4. Tap and cable

at the fixtures = tap − voltage drop

We pick the lowest tap that keeps the voltage in the fixture range. With "Pick for me", we try 12, then 10, then 8 AWG.

Resistance of stranded copper at 75 °C, from MSU Tech Note 227, Table 227.1 (source)
Cable sizeOhms per 1,000 ft
16 AWG4.99
14 AWG3.14
12 AWG1.98
10 AWG1.24
8 AWG0.778

Limits

  • We put all fixtures of a run at its end. This is the worst case. Fixtures along the run get less voltage drop.
  • We use the resistance of copper at 75 °C. MSU says that this value is about 8% higher than at 50 °C. So the real voltage drop is usually a little lower.
  • We find the current at 12 V. The real current can change with the voltage at the fixtures. Measure the voltage after the install.
  • We do not check the current rating of the cable or of the transformer circuits. Your installer checks them.
  • We do not check light levels, glare or aiming.
  • The sea turtle check uses the state model ordinance. The local ordinance can be different.

Sources

We read each source on the date shown. Each rule, table value and price on this page comes from one of these sources.

  1. Electrical Tech Note 227: Sizing Conductors to Minimize Voltage Drop. Michigan State University, Biosystems and Agricultural Engineering Department. Equation 227.1: voltage drop = 2 x current x resistance of the one-way length. Table 227.1: dc resistance of stranded copper at 75 °C in ohms per 1,000 ft. The note names Table 8 of the National Electrical Code as a reference table for these values. It says that the values at 75 °C are about 8% higher than at 50 °C. https://www.maec.msu.edu/download_file/view/147/303. Read on .
  2. Electrical Tech Note 212: Conductor Properties. Michigan State University, Biosystems and Agricultural Engineering Department. Table 212.1 gives the same resistance values. Copper resistance changes about 8% for a 25 °C change in temperature. https://www.maec.msu.edu/download_file/view/afde3b6d-acc5-441b-839a-59a2fe7026bd/303. Read on .
  3. Low-Voltage Transformer Installation Guide, Multi-Tap Transformers. VOLT Lighting. Total fixture watts at most 80% of the transformer capacity. Taps of 12, 13, 14 and 15 V. A good range at LED fixtures is 10.8 to 15 V. No runs longer than 300 ft. Cable chart with 12/2, 10/2 and 8/2 cable. Steps for the mounting height, the GFCI outlet, the distance from water and the voltage check at night. https://volt-product-docs.s3.us-east-2.amazonaws.com/is-vmultitap-ver1.pdf. Read on .
  4. How to Create a Landscape Lighting Installation Plan (May 20, 2020). VOLT Lighting. Runs of about 100 to 150 W. Divide an area of more than 150 W into two runs. Watts times feet check for 12 and 10 gauge cable. Most makers recommend no more than 80% of the transformer rating. https://www.voltlighting.com/learn/create-a-landscape-lighting-plan. Read on .
  5. Pro-Contractor Transformer 150 W (15PC150SS) product page. Kichler Lighting. A second maker with the same sizes: 75, 150, 300, 600 and 900 W. https://www.kichler.com/products/landscape-lighting/landscape-accessories/transformers/pro-contractor-series-15v-transformer-150w-15pc150ss. Read on .
  6. Clamp-Connect 150 Watt (12v/15v) Multi-Tap Low Voltage Transformer. VOLT Lighting. 150 W size with 12 V and 15 V taps. Price: as low as $229.99. https://www.voltlighting.com/clamp-connect-150-watt-12v-15v-multi-tap-low-voltage-transformer. Read on .
  7. 300 Watt (12v-15v) Multi-Tap Low Voltage Transformer. VOLT Lighting. 300 W size, 12 to 15 V. Price: as low as $229.99. https://www.voltlighting.com/300-watt-12v-15v-multi-tap-low-voltage-transformer. Read on .
  8. 600 Watt (12v-15v) Multi-Tap Low Voltage Transformer. VOLT Lighting. 600 W size, 12 to 15 V. Price: as low as $274.99. https://www.voltlighting.com/600-watt-12v-15v-multi-tap-low-voltage-transformer. Read on .
  9. Pro 900W 12V-22V Low Voltage Transformer. VOLT Lighting. 900 W size, 12 to 22 V. Price: as low as $549.99. https://www.voltlighting.com/900-watt-12v-22v-multi-tap-pro-transformer. Read on .
  10. Pro 1200 Watt 12-22v Landscape Lighting Transformer. VOLT Lighting. 1200 W size, 12 to 22 V. Price: as low as $699.99. https://www.voltlighting.com/low-voltage-transformer-outdoor-lighting-1200. Read on .
  11. 16/2 Direct Burial Cable (250 Feet). VOLT Lighting. Price: $94.99 for 250 ft. https://www.voltlighting.com/16-2-250-cable. Read on .
  12. 14/2 Direct Burial Cable (250 Feet). VOLT Lighting. Price: $112.99 for 250 ft. https://www.voltlighting.com/14-2-250-cable. Read on .
  13. 12/2 Direct Burial Cable (250 Feet). VOLT Lighting. Price: $145.99 for 250 ft. https://www.voltlighting.com/12-2-250-cable. Read on .
  14. 10/2 Direct Burial Cable (250 Feet). VOLT Lighting. Price: $235.99 for 250 ft. https://www.voltlighting.com/10-2-250-cable. Read on .
  15. 8/2 Direct Burial Cable (250 Feet). VOLT Lighting. Price: $469.99 for 250 ft. https://www.voltlighting.com/8-2-250-cable. Read on .
  16. Warranty Information. VOLT Lighting. Lifetime warranty on brass and copper spot, flood, path and area fixtures. 5 years on aluminum spot, flood, path and area fixtures. https://www.voltlighting.com/warranty. Read on .
  17. NFIP Technical Bulletin 8: Corrosion Protection for Metal Connectors and Fasteners in Coastal Areas (June 2019). Federal Emergency Management Agency (FEMA). Similar metals (Sec. 5.1.2). Salt spray and the distance from the shore (Sec. 6.2). Sheltered areas under decks (Sec. 6.4). Inspection at least once a year (Sec. 6.5). Type 304 or Type 316 stainless steel (Sec. 8.2). https://www.fema.gov/sites/default/files/2020-07/tb8-corrosion_protection_metal_connectors_coastal_areas.pdf. Read on .
  18. Rule 62B-55, F.A.C., with the State of Florida Model Lighting Ordinance for Sea Turtle Protection (effective December 15, 2020). Florida Fish and Wildlife Conservation Commission (copy of the rule and the model ordinance). The 26 counties with nesting beaches (62B-55.003). The model is guidance for local rules (62B-55.004). Model definitions (Sec. 1.4), the lighting district (Sec. 2.1), new structures (Sec. 3.2), outdoor areas (Sec. 3.3), pools (Sec. 3.5), existing lights (Sec. 3.7), piers (Sec. 3.8) and the nesting season guidance. https://myfwc.com/media/26205/model-lighting-ordinance.pdf. Read on .

Ask a lighting designer about this project

Send your plan to Holzer Lighting in Boca Raton, Florida. Holzer Lighting designs, specifies and buys lighting for owners, managers, designers and builders.

A designer reads your brief and contacts you. The designer checks the rules, the light levels and the prices for your site. This page gives planning estimates only.

You can also email info@holzerlighting.com or call 561.508.8990.

About Holzer Lighting

Other free lighting tools:

Holzer Lighting gets your details and the project brief from this page. They use them only to answer you.